Відео

Thank you for this video and sharing the settings you found. I almost gave up on PETG. Had exactly the same problems like in your video. Now printing with Bambu Labs PETG works almost perfect.

Wow dell made this 10 years ago?

Whitch settings did you use? Is it Bambu Lab basic PETG?

Saved my bacon, thanks.

40%? Damn that’s doodoo

Thanks so much for sharing, after following the settings my petg prints are almost perfect. But I noticed that theres always bit of sagging on one side of the print, I wonder is it caused by fan speed settings? Im also on P1S

where autolight? forgot to review😅

more retract, less speed, dry filament, adjust temp

Dry out your filament. I have a little toaster oven and I put it in "Warm" mode and toss the whole TPU roll in there for 3 hours then print with it. Much better result.

That filament is wet as hell

Looks like adhesion issues to me, try washing it and put some glue on ut

Did you dry out the filament?

Failure is only the beginning dawg Try again fail fail again but fail again better next time

Turn on in skin travels. Should help with the stringing.

This is your issue. You have wet filament.

I use this device as a UPS. It seems to work stably, there has never been any breakdown or malfunction. Having charged its batteries, it simply passes through itself the voltage from the outlet to the consumers connected to it. The device itself is damn good. It is also worth noting the very durable lithium iron phosphate batteries with a stated huge number of charge-discharge cycles. The only serious drawback is that when used as a UPS and simply while charging from a socket, it periodically turns on a very noisy cooler to cool down; even turning on quiet mode in the application does not help with this

Looks to have done a fine job of cooking. Steamed Fish may be an option, especially with Ramen.

can this be used as a full ups mode? like without plugging out the charger? what happens if its fully charge will the charger automatically cuts the power?

Thank you i was trying to print a robotic arm with petg but my print was not sticking to the bed , it was stringy, printed noodles . Thank You . this helped ,p1s.

He was carrying all the time

Great write up and worked wonders. Thank you! What are your cooling settings under the filament settings?

Thanks for the settings

It is nice but doesn't look anything like the one from the movie prop.

Okey thanks for the vid... "P1S PET-G settings for successful 3D prints" that is your titel. can you share your setting then?

Bambu was too cheap for the $2000 printer to just put a rechargeable dehydrator in? lol They cost like $15

On a 20,000 mAh battery pack how long should this last ? We are not sure. Any info kindly appreciated.

Thank you for sharing! I’m going to try printing with PETG this evening so I’m glad I found this! I was about to send the print with the default print speeds on the x1c 😅

I could not find the speed mode within the setting in my account, is the speed mode accessed on the printer itself or is there a way to access the speed mode?

NBA Finals? Did I read the caption correctly?

Not NBA finals Btw

i see lebron

Carry

Yet nobody cares if it were Lebron or curry or luka

it seems you dont know nba rules. without trolling, thats not a travel call. he can do 3000 steps while the ball is in the air

salty

Carry is carry. Doesn't matter where on the court it is.

like any of that wouldve mattered

in the backcourt, doesnt effect play at all. no one will call it, and its stupid to call that.

Thats not fair we should have won that game😢

This a reach , that’s not a carry

as a bucks fan it’s annoying but a lot of people doing that. also it’s the playoffs not finals

No he bounced before the third step

thanks for the video :)

This was a fantastic guide. I was about to give up on using PETG with X1C. The lower speed and infill made the difference. Thank you for posting! I did have one question regarding PETG still getting stuck to the stock tip and riding up the boot any suggestions?

links ?

really helped me, thank you. curious if you are leaving the printer enclosed (top and door closed?). also pretty comical how bad bambu's own settings are, even with their own filament....

i have a print dimension issue. I’m trying to print a round part that’s 2.0 inch diameter 1 inch tall. . The part is coming out 2.000 on one side and if i check a different spot (180) it’s at 1.990 ( .010 difference) out of round. How can i get this dimensions closer to 2.0 inches diameter? I have default settings pla P1S

Wow that is the kind of videos that we need…take the power stations to real life tasks ,not just charging phones ,we have power banks for that .what is the bran of that 12 volt cooker Sir ?🤩🤩🤩🤩🤩 to the video

Bro got the same printer it is amazing isn’t it only had it for a few weeks but still amazing

Where’s the spreadsheet